Discovering Essential Plumbing Skills is Important When Installing a Bathtub
Discovering Essential Plumbing Skills is Important When Installing a Bathtub
Blog Article
Just how do you really feel in regards to How to Install a Bathtub?
Installing a bathtub isn't exactly brain surgery, yet it does call for strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably hard task. If the old bathtub is easily easily accessible, the job can move rapidly; if you have to open up a wall to remove the old bathtub as well as position the brand-new bath tub, the job is a lot harder. In either situation, the project is within a house handyman's skills, although you will need an assistant to vacate the old bathtub and set in the brand-new one. Make certain you have certified yourself for the work and also are comfortable attempting it. As opposed to employing a professional to take over a halfway-completed task, it is better to take into consideration using one before you begin. Chances are you may require a specialist plumber to make tube connections.
This short article will certainly aid you install a brand-new bath tub in your washroom if you have actually currently bought a new bathtub and also do not require to alter the plan of your previous water system pipes.
Your tools and also product checklist should consist of the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is disconnect the water. After doing so, switch on the faucets to drain pipes any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite problematic due to the limited accessibility that is usually the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from turning throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Prior to going on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin making sure that the washers are in area in between the faucet and also the sink. Protect the tap in position with the maker supplied backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous kind needs to be attached to the faucet ends first, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Mounting the Bathtub
Making use of both wood boards under its feet, put the bath tub in the needed placement. The wooden boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four small factors.
The next goal is to guarantee that the bath tub is leveled all round. This can be attained by examining the spirit level and changing the feet on the bath tub up until the level reads degree.
To install taps, fit the bottom of the furthest adaptable faucet adapter to the ideal supply pipe by making a compression join; after that do the same for the various other faucet.
Turn on the water system and examine all joints as well as brand-new pipework for leaks as well as tighten them if necessary. Fill the bath tub and also inspect the overflow outlet as well as the regular electrical outlet for leakages.
Finally, deal with the bath paneling as defined in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait until the tub has been made use of a minimum of when as this will resolve it right into its final setting.
Preparing for the Setup
To start with, the sustaining framework provided with the bath should be fitted (if needed) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the faucet features a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets system to prevent pressure on the bathtub.
Fit the versatile tap ports to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you utilize every one of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be suited its last position.
Tiling Around the Tub
In the area where the bath fulfills the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture an inflexible seal, triggering the water to permeate the wall between the bathroom and also the tiling, bring about issues with dampness as well as possible leaks to the ceiling below.
You can select from a variety of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to always fill the tub with water before sealing, to allow for the motion experienced when the bathtub is in usage. The sealant can break relatively very early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also quickly available on the marketplace. It is a good idea to fit the tiles using water-resistant or water-proof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen person who reads about How to Install a Bathtub, I was thinking sharing that topic was a good idea. Do you know about somebody who is fascinated by the niche? Do not hesitate to promote it. I treasure reading our article about Installing A Bathtub.
Trusted for emergency plumbing excellence. Report this page